EP model substitute gearbox for woods rotary gearbox

NEW forty HP GEARBOX Sleek Enter 1 3/8 twelve spline output Interchangable with industry common measurement i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Many Much more

Attributes
(1) brand name new forty five horse electricity shearpin gearbox. This gearbox fits numerous diverse can make of 4′,5′ and some 6′ rotary cutters. I promote a great deal of these containers every 12 months for several diverse apps and carry ALL Substitute Elements for this box, but hopefully you will not have to fret about that.
Right here are the specs on the box:
*45 horse energy gearbox
*Common one-3/eight” sleek input shaft(the place the pto shaft hooks on). The pto shaft is held on by a 1/two shearbolt.
*length of the enter shaft out of the gearbox is 3″ lengthy
*bolt hole sample for mounting is on the corners, 4-three/4 heart of gap to heart of gap. It takes a 5/eight” bolt.
*twelve splined output shaft(the place the blade carrier hooks up on the bottom)
*one-nine/16 exterior measurement in excess of the output shaft splines- from the base of the output cap to the conclude of the splines is 2-3/4″ lengthy- general length of the output shaft is 4-1/two” lengthy.
*requires a one” threaded castle nut and a carter important on the bottom of the output shaft to secure blade pan(NUT is provided – – BLADE PAN IS NOT!!)
*general top of the box from the prime of the mower deck to the best of the box is 9-one/two”
This is a pretty large product (47 lbs.) so freight is not inexpensive, but we do not make anything off of freight, whatever ups expenses us we demand you.
40 HP
one:1:forty seven Ratio
1-3/eight” Easy Input Shaft with Shear Pin Hole
one-one/2″ twelve-Spline Ouput Shaft
Bolt Sample: 6-one/2″ (four) five/eight” Holes, five” Center Gap Required for Shaft Assembly
The Enter and Output Shafts Cannot be Acquired Serparately.
They are Bought as a kit.
The kit includes the pursuing elements: enter shaft, enter equipment, output shaft, output equipment.
The Shaft Kit Can not Be Separated.

EP model substitute gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or in any other case doing improperly? You’ve appear to the right area.

Read through under for the most common troubles with rotary cutter gearboxes and their answers (from swift and dirty, to specialist).

Leaking Base Seal:
If you have wrapped some baling or fencing wire about your output shaft and blown the seal, the specialist thing to do is to change the seal.
If your output seal is intact, and you are capable to get ID, OD and thickness measurements (in millimeters), most bearing homes can buy you up a generic double-lip seal that will get you back again up-and-working. If not, give us a call and we can support you type out what you want.
A dental decide is the least difficult way to eliminate the aged seal prior to pressing in the new 1.
If you happen to be fortunate ample to have a slow-leak, the fast and soiled approach is to operate automotive-type grease in the gearbox till the new seal will come in. Be sure to examine and include grease more usually than you would with oil, as this is NOT a professional repair.

Broken Output Shaft:
Uh oh. You hit anything that failed to shift. The great information is that the output shaft on most gearboxes is relatively effortless to replace. The bad information is… it is hardly ever an isolated failure.
The very first thing to do is to just take aside your gearbox and assess the entire extent of the hurt. If it is truly just the output shaft, you ought to be ready to change it out, no dilemma. The output shafts commence at about $70 and go up in price dependent on the measurement of the gearbox.
However, in most circumstances, the bearings ($20/ea), seals ($ten/ea) and equipment-set ($70) will also normally take a beating. If you might be unlucky, the output cap ($80) will also undergo some damage.
In this scenario, it is generally less expensive to substitute the gearbox. Assess the price of elements to the price of an complete, new, warrantied gearbox. Often, even pros have to know when to contact it a day.

I Want to Change my Enter Shaft:
If you are fatigued of shifting shear pins or seeking back and viewing that your mower hasn’t been reducing, you might want to put in a slip-clutch pto shaft (Of course, we sell individuals way too).
This normally demands putting in a 540-fashion, 6-spline enter shaft ($85) on your mower’s gearbox.
Blessed for you, we did a compose-up on our blog. It is referred to as “How to change the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all audio type-of similar more than-the-mobile phone. The ideal factor to do is to disassemble your gearbox and get a seem at the gears and bearings. The problem will normally current alone in the way of broken/lacking gear tooth, toasted gears (like that photograph on our residence web page), or blown bearings.
If every little thing appears typical, try out altering the equipment-mesh. This is done with the mylar “gaskets” that sit in between the principal gearbox scenario and the enter/output caps. Attempt adding or taking away some of these spacers right up until your gears have approximately one/eight”-1/four” of totally free perform. Experts can purchase replacements ($1-2) in varying thicknesses, but we suggest the swift and dirty technique of slicing your personal out of a sheet of mylar.
Do not neglect to re-seal the gearbox with RTV soon after you’ve located the proper blend. Even although they are referred to as “gaskets”, they will not seal your gearbox on their very own.

If just recently you, among your close friends or family member had any type of encounter with Gearbox For Rotary Cultivators, do not hesitate to share your point of view in comments.